Tutorial: Programming arduino through xbee | Test & Recommendation

  • Arduino Programming in 24 Hours, Sams Teach Yourself
  • In ZIYUN,Xbee USB adapter (FTDI ready),Applicable micro Arduino master program for programming, can upload your program through the wireless controller module/wireless real-time data transmission
    Used for the XBee module configuration parameters Easily connected to a PC via mini USB cable XBee-setting support software X-CTU Also used as a USB-TTL adapter Voltage: +5V(USB Power)
  • Raive Electronics USB Data Sync Cable for Arduino UNO/Arduino Mega 2560 Rev 3 R3 Microcontroller - 10ft
    ✔ Brand new and high quality ✔ Length: 10ft (plug to plug) ✔ USB Cable to connect Arduino UNO/Arduino Mega 2560 Rev 3 R3 Microcontroller to a PC or Mac
  • Green Light Optical Fingerprint Reader Sensor Module Compatible withArduino Raspberry Pi ESP8266 ESP32
    Document link: https://tinyurl.com/Fringerprint-Sensor Adapter FTDI FT232 Cable link:https://www.amazon.com/dp/B014GZTCC6 Connection with diymall R3 board:pin #2 is IN (GREEN wire),pin #3 is OUT (WHITE wire),5V connect sensor (Red wire),GND connect sensor (Black wire) Connection with diymall 2560 board:pin #10 is IN (GREEN wire),pin #11 is OUT (WHITE wire),5V connect sensor (Red wire),GND connect sensor (Black wire) Use:Typically used in safe -there's a high powered DSP chip that does the image rendering, calculation, feature-finding and searching What you will get is: 1 x Optical Fingerprint Reader Sensor Module. If any question, pls contact us by email.You can find " Sold by DIYmall" under Buy Now button, click "DIYmall" and you will get to a new page, click "Ask a question".
    25.99 $
  • DAOKI 10PCS MOSFET Button IRF520 MOSFET Driver Module 3.3V-5V Power for Arduino MCU ARM Raspberry pi
    This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067. (COM in the schematic, SIG on the board)to one of 16 channel pins (CHANxx). It works with both digital and analog signals (the voltage can’t be higher than VCC), To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), This allows you to connect up to 16 sensors to your system using only 5 pins!
    9.79 $
  • Gikfun Bluetooth XBee Shield V03 Module Wireless Control for ZigBee Arduino (Pack of 2pcs) EK1185x2
    Bee Adapter is a compact USB to serial adapter equipped with BEE (20pin 2.0mm) sockets, can achieve a simple two crunodal ZigBee network. It can be used for programming or communicating with board which basic Arduino but without USB interface Easily connected to a PC via mini USB cable. It is a fully Assembled shield without the XBee module
    12.68 $
  • LuxtechPro Speech Recognition Module ELECHOUSE Voice Recognition V3 Interface 5V TTL Level UART/GPIO
    This module is a compact and easy-control speaking recognition board. It is a speaker-dependent voice recognition module. It supports up to 80 voice commands in all. Max 7 voice commands could work at the same time. Any sound could be trained as command. Users need to train the module first before let it recognizing any voice command. It has 2 controlling ways: Serial Port (full function), General Input Pins (part of function). General Output Pins on the board could generate several kinds of waves while corresponding voice command was recognized. We already know that Voice Recognition module V2 supports 15 commands in all and only 5 commands at the same time. On V2, voice commands are separated into 3 groups while you training it. And only one group (5 commands) could to be imported into Recognizer. It means only 5 voice commands are effective at the same time. On V3, voice commands are stored in one large group like a library. Any 7 voice commands in the library could be imported into recognizer. Parameters: Voltage: 4.5-5.5V, Current: <40mA, Digital Interface: 5V TTL level for UART interface and GPIO, Analog Interface: 3.5mm mono-channel microphone connector + microphone pin interface. Size: 31mm x 50mm. Recognition accuracy: 99% (under ideal environment). Features: Support maximum 80 voice commands, with each voice 1500ms (one or two words speaking). Maximum 7 voice commands effective at same time. Arduino library is supplied. Easy Control: UART/GPIO. User-control General Pin Output.
    38.89 $
  • HC-05 6Pin Wireless Bluetooth Module, RF Transceiver Master-Slave 2in1 RS232 TTL Serial Configuration at Mode Breakout Board Compatible with Ard-uino
    Bluetooth module HC-05 Master and slave Two in one module. The factory setting is slave mode, but you can set this module to master mode so that you might be able to connect to other Bluetooth 2.0 devices.HC-05 Wireless BT Module. HC-05 Wireless BT Module: with this HC 05 Bluetooth module,You can quickly add the Bluetooth feature to your Ard-uino project, and then you can use your android phone to control some gadgets, such as: switch, LED. Master and Slave 2-IN-1 HC 05 Module:Working Voltage 3.6V to 6V , Default baud rate:9600,Default pin:1234. Button: Press the button, the module enter the AT mode. AT commands are executed only in AT mode.
    13.99 $
  • Keywish Project AE-01 Scratch Starter Kit for Arduino R3 Mega328 with 30 Lessons Tutorial Compatible with Arduino IDE Mixly Sctratch Mblock Graphical Programming
    Free PDF tutorial (30 lessons) Contains basic courses, sensor courses, comprehensive experimental courses from easy to difficult Support Arduino IDE, Mixly, mblock Scratch graphical programming. High quality kit with Development Board. 100% compatible with Arduino UNO R3 This is the most basic Arduino kit for the beginner, has all the component you need to start Arduino Tutorial Link:github.com/keywish/keywish-uno-starter-kit
  • CAN-BUS Shield Compatible with Arduino and Seeeduino
    Implements CAN V2.0B at up to 1 Mb/s SPI Interface up to 10 MHz Standard (11 bit) and extended (29 bit) data and remote frames Two receive buffers with prioritized message storage Industrial standard 9 pin sub-D connector, Two LED indicators