Tuto: Arduino programming ppt | Forums Ratings

  • Makerfire 10pcs Arduino NRF24L01+ 2.4GHz Wireless RF Transceiver Module New
    Brand New, 90 Days Warranty Model: NRF24L01
  • Longruner Mini V3.0 ATmega328P 5V 16M Micro Controller Board Module for Arduino (10pcs)
    CH340G Replace FT232RL Micro-controller ATmega328P Using Atmel atmega328p-au MCU, support ISP download; support USB Download and Power. Support for external 5V 12V DC power supply; support power supply by 9V battery. 10pcs Mini V3. 0 ATMEGA328P Improved version with 3pcs pin headers (2pcs 15pin headers +1pcs 6pin headers).
  • HiLetgo 2pcs MCP2515 CAN Bus Module TJA1050 Receiver SPI Module for Arduino AVR
    Supports CAN V2.0B specification, the communication speed 1Mb/s. 5V DC power supply module, SPI interface protocol control. Working current: 5mA (1 microamp standby current. Except the power indicator). 0 to 8-byte data field. With standard frame, expand the frame and remote frame. 120 ohm termination resistors. With impedance matching, ensures the drive capacity, long-distance data transmission against signal radiation.
  • Comidox 4PCS MCP4725 Breakout Module I2C DAC 12Bit Development Board 2.7V to 5.5V Supply with EEPROM for Arduino Raspberry Pi
    The MCP4725 is a single-channel 12-bit buffered voltage output DAC with non-volatile memory (EEPROM) that allows you to store configuration register bits (2 bits) and DAC input data (12 bits) to non-volatile EEPROM (14-bit) In memory. The DAC can be configured for normal mode or power-saving shutdown mode by setting the configuration register bits. The DAC allows you to send analog signals, such as sine waves, from a digital source such as the I2C interface on an Arduino microcontroller. Digital to analog converters are ideal for sound generation, musical instruments and many other creative projects. This version of the CJMCU-MCP4725 Breakout solves some of the board's problems, including IC packages, I2C pinouts, changing the overall board size to better suit your project, and some minor adjustments. The board breaks down each pin you need to access and uses the MCP4725 (including GND and signal OUT pins) to connect to the oscilloscope or any other device you need to connect to the board. There are also SCL, SDA, VCC and another GND for the basic I2C pinout. The device can be used with a 2-wire I2C-compatible serial interface and is powered by a single supply from 2.7V to 5.5V. If you want more than one MCP4725 on the bus, you can disable the pull-up resistors on this board.
    7.49 $
  • HiLetgo GY-906 MLX90614ESF Non-contact Infrared Temperature Sensor Module IIC I2C Serial for Arduino
    MLX90614 is an infrared thermometer for non-contact temperature measurements. Both the IR sensitive thermopile detector chip and the signal conditioning ASIC are integrated in the same TO-39 can. Integrated into the MLX90614 are a low noise amplifier, 17-bit ADC and powerful DSP unit thus achieving high accuracy and resolution of the thermometer. The thermometer comes factory calibrated with a digital SMBus output giving full access to the measured temperature in the complete temperature range(s) with a resolution of 0.02°C. The user can configure the digital output to be pulse width modulation (PWM). As a standard, the 10-bit PWM is configured to continuously transmit the measured temperature in range of -20 to 120°C, with an output resolution of 0.14°C.
    14.99 $
  • DAOKI 5Pcs Speed Measuring Sensor LM393 Speed Measuring Module Tacho Sensor Slot Type IR Optocoupler for MCU RPI Arduino DIY Kit with Encoders
    1.the use of imported groove coupler sensor, slot width 5mm. 2.output status indicator lamp output high, output low lights. 3.block, output high; no shelter, output low. 4.the comparator output signal clean, good waveform, driving ability, than 15mA. 5.the working voltage of 3.3V-5V
    6.49 $
  • HiLetgo 5pcs DS3231 High Precision RTC Real Time Clock Module 3.3V/5V for Arduino Raspberry Pi
    High Precision DS3231 RTC Real Time Clock Module Two calendar clock Reset output and anti-shake inpu High speed (400 KHZ)I2C serial bus Precision of digital temperature sensor is ¡À3¡ãC
    13.99 $
  • Keywish Project AE-01 Scratch Starter Kit for Arduino R3 Mega328 with 30 Lessons Tutorial Compatible with Arduino IDE Mixly Sctratch Mblock Graphical Programming
    Free PDF tutorial (30 lessons) Contains basic courses, sensor courses, comprehensive experimental courses from easy to difficult Support Arduino IDE, Mixly, mblock Scratch graphical programming. High quality kit with Development Board. 100% compatible with Arduino UNO R3 This is the most basic Arduino kit for the beginner, has all the component you need to start Arduino Tutorial Link:github.com/keywish/keywish-uno-starter-kit
    29.99 $
  • DIYmall Laser Transmitter Module forArduino (Pack of 10pcs)
    Voltage:5V, Power:5Mw, Wave length:650nm, OD:6mm NOTE: Please do not point to anyone, especially their eyes Package Includes: 10pcs Laser Transmitter Module
  • RobotDyn - Arduino Audio Sensor, Arduino Frequency Detector Module Attachable to Arduino, Arduino Microphone Module- Sensor with Digital and Analog Output - for Arduino, STM32, Raspberry DIY Projects
    ✔️ HIGH QUALITY AND PREMIUM MADE: The most widely used Arduino Audio Sensor, Differentiates from other cheaply made Arduino Frequency Sensor/Arduino Sound Sensor by being High Quality and not made by third party vendors. All is created through Robotdyn Experts. ✔️ TECHNICAL SPECS: There is a mounting screw hole 3mm. Use 5v DC power supply. There is a threshold level and output flip. ✔️ The Sound Detector has two outputs:AO - Analog output, real-time output of the microphone signal.DO - When sound intensity is below a pre-defined threshold, the output is low. ✔️ THRESHOLD SENSITIVY CAN BE ADJUSTED: When sound intensity raises above that threshold, the output is high. The threshold (sensitivity) can be adjusted via the potentiometer onthe sensor. ✔️ THE SOUND DETECTOR MODULE: is based on a microphone and a power amplifier. It can be used for detecting the sound strength of the environment. The value of digital output can be adjusted by the potentiometer.