Tuto: 3d printer controller | Evaluation

  • BIGTREETECH 3D Printer Part SKR V1.4 Turbo 32bit Control Board Smoothieboard&Marlin Open Source SKR V1.4 SKR V1.3 Upgrade Support TMC2209/TMC2208/TMC2130 Drivers (SKR V1.4 Turbo)
    🌻【32 Bit High Performance Microprocessor】SKR V.4 Turbo silent board adopts 32 bit ARM level Cortex-M3 series LPC1769,120MHz frequency m icroprocessor, which can reduce the stepper motor noise greatly, a choice to be your 3D printer controller. 🌻【Multiple Function】 SKR V1.4 Turbo motherboard supports resume printing while power Of,filament break detection and automatic shutdown after printing function.In the meanwhile,it can Support TFT2.4, TFT70, TFT3.5 inch colorful touch screen and 2004LCD,12864LCD screen. 🌻【Compatible with Multi-Stepper Motor Drivers 】 On-board TMC driver SPI operating mode and UART operating mode ,Support stepper driver TMC5161, TMC5160, TMC2209, TMC2225, TMC2208,TMC2130, ST820, LV8729, DRV8825, A4988, etc. 🌻 【 Easy and Simple to Flash Firmware】Firstly download firmware of SKR V1.4 motherboard,copy and save it to SD card.firmware must bed reserved ,then re-plug the SD card and wait to 10s.The firmware has been successfully updated when the progress bar and interface appear. 🌻【Reserve BLTouch interfaces 】 Reserve BLTouch interfaces SERVOS and Probe for easy to connect with BLTouch.
  • BIGTREETECH TFT35 V3.0 Graphic Smart Display Controller Board for 3D Printer Ramps 1.4 RepRap 3D Printer Can Select Two Work Modes
    1.Upgrade the firmware by SD card. It is easy and convenient to operate.This display board has higher compatibility. Users can select two work modes,they are UART serial port screen mode and 12864 screen mode. 2.Serial port screen mode supports two printing modes: SD card and U disk. 3.Reserve WIFI port, and WIFI function is realized by external WIFI module; 4.Reserve the extension port of filament breaking detection (FIL-DET);Reserve the extension port of automatic shutdown after printing (PS-ON); 5.2 sets of UART serial port extension ports are reserved for DIY use.
  • BIGTREETECH SKR V1.4 Turbo 32bit Controller Panel Board for 3D Printer Compatible With12864LCD/ TFT24 Support 8825/TMC2208/Tmc2130 (with 5TMC2209)
    TMC2209--The motor is not easy to lose step; ultra-quiet mode; TMC2209--A large area of thermal pad, reduce the temperature of the driving work; TMC2209--Prevent motor shake;Support stall detection;Support STEP / DIR and UART mode SKR V1.4 Turbo Using 32-bit 120MHz ARM-class Cortex-M3 series LPC1769 main control chip, the performance is greatly improved;1-way CNC fan,3-way Frequent fans.
  • BIQU LCD 12864 Version Graphic Smart Display Controller Module with Adapter and Cable for RAMPS 1.4 Reprap 3D Printer Kit
    A LCD display module with blue backlight, small and light appearance, suitbale for copiers, fax machines, laser printers, industrial test equipment, networking Small and light appearance, it is easy and convenient to use Suitable for copiers, fax machines, laser printers, industrial test equipment, networking equipment etc LCD control panel through which you can achieve spooling is the 3D model Gcode files are copied to the SD card, and then print the file via the LCD control panel This version is an upgraded version of reprap smart controller
    15.99 $
  • BIQU MKS-Base V1.6 Plate Controller Board for 3D Printer Ramps 1.4
    Arduino MEGA compatible Atmega2560 and FT232 processors are compatible with all RAMPS class firmware Firmware can use the same configuration as ramps1.4 Easy DISPLAY + SD-CARD connector,RepRapDiscount SmartController compatible pin header on board Easy connect MKS TFT on AUX-1 3x temperature ADC connectors for thermistors
    34.99 $
  • BIGTREETECH SKR Mini E3 V2.0 Control Board 32Bit New Upgrade for Creality Ender 3, with TFT35 E3 V3.0 Graphic Smart Display Controller Board 3D Printer Parts
    【TFT35 E3 V3.0】 ARM Cortex-M3 series STM32F207VCT6 chip with 32-bit CPU 120MHz; Upgrade the firmware by SD card. It is easy and convenient to operate. 【SKR Mini E3 V2.0】 ARM Cortex-M3 Series STM32F103RCT6 Master Controller with 32-bit Main Frequency of 72MHz Chip;Integrate UART mode of TMC2209 to simplify debugging of motherboard and driver.Reserve expansion ports for TMC2209 pins to facilitate users to use DIAG instead of Endstop. 【TFT35 E3 V3.0】 This display board has higher compatibility. Users can select two work modes:UART serial port screen mode and 12864 screen mode;Serial port screen mode supports two printing modes: SD card and U disk. 【TFT35 E3 V3.0】 LCD12864 mode uses EXP1, EXP2 and EXP3. EXP1 and EXP2 are LCD screen ports of normal motherboard. EXP3 is the LCD interface used by E3 series motherboard (such as SKR MINI E3 V1.2, SKR E3 DIP V1.1, etc.) 【SKR Mini E3 V2.0 Firmware】 https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/tree/master/firmware/V2.0 ;【TFT35 E3 V3.0 Firmware】 https://github.com/bigtreetech/BTT-TFT35-E3-V3.0.
    82.99 $
  • FYSETC 3D Printer Parts Clone 7 inch PanelDue Touch Screen Controller 7i Integrated Paneldue Colour LCD Display for DuetWifi Duet 2 Ethernet
    Clone Parts for DIY 3D Printer, compatible with DuetWifi Duet 2 Ethernet; Resolution of 800×480 pixels on a 7 inch LCD. 5V power from host 3D printer controller, 2-wire async serial interface with 3.3V signal level (5V tolerant input). Connections to the onboard micro SD card socket as well as the PanelDue serial and power connections are all available via a 10-way ribbon cable. A 300mm long ribbon cable (maximum recommended length) is supplied. 4-wire cable to connect the PanelDue to your controller board for the serial and power connections. This cable is also supplied with the package.
    94.99 $
  • BIGTREETECH SKR V1.3 Control Board 32bit 3D Printer Parts for TFT35/12864LCD/TFT24 Support DRV8825/TMC2208/Tmc2130 (with TFT35 V2.0)
    TFT 3.5-inch color touch screen with skr v1.3 32-bit motherboard. TFT3.5-inch color touch screen, provides continuous software upgrades, easy to upgrade. The Master program without modification, plug and play, supports Marlin, Repetier, Smoothieware firmware. TFT35 V1.2 supports image customization, boot logo, all button images can be designed. Supported 7 custom buttons. SKR V1.3 Equipped with highly modular Marlin2.0 open source firmware and smoothware, it is convenient for users to take advantage of DIY and secondary development. This eliminates the concern that the core code can not be mastered.
    44.99 $
  • KINGPRINT TMC2208 V3.0-UART with SKR V1.3 32bit Smoothieware Controller Panel Board for 3D Printer Compatible With12864LCD/Support A4988/8825/TMC2208/TMC2100 Drivers
    1.The performance of the ARM-class Cortex-M3 series LPC1768 main control chip with 32-bit frequency and 100MHz is greatly improved;Reserve the extended port SERVOS of the PWM signal to support BL Touch 2.Support Resume Printing While Power Off,Filament Break,CE Certification to adopt 4-Layer PCB with “Gold deposition technology” which capability is more stable and better heat dissipation 3..Onboard TMC2130 driven SPI mode of operation and TMC2208 driven UART mode,The utility model eliminates the complicated wiring process and can be used only by simply plugging and unplugging the jumper cap; 4.The high-performance MOSFET tube has better heat dissipation effect; it supports functions such as power-off continuous shooting, material cut detection, and shutdown; 5.Use the power selection design ,to separate the USB power supply from the switching power supply, effectively avoiding short circuits,Causes the computer's USB port to be burned;
  • BIGTREETECH TFT24 V1.1 Graphic Smart Display Controller Board for 3D Printer Ramps 1.4 RepRap 3D Printer Can Select Two Work Modes
    BIGTREETECH TFT24-V1.1 is a small volume ultra-clear 3D printer display board. It can work in two modes. ARM Cortex-M3 series STM32F105RCT6 chip with 32-bit CPU 72MHz; Upgrade the firmware by SD card. It is easy and convenient to operate.Serial port screen mode supports two printing modes: SD card and U disk This display board has higher compatibility. Users can select two work modes, they are UART serial port screen mode and 12864 screen mode.