Top3: Arduino programming ppt | Customer Evaluation

  • HiLetgo GY-906 MLX90614ESF Non-contact Infrared Temperature Sensor Module IIC I2C Serial for Arduino
    MLX90614 is an infrared thermometer for non-contact temperature measurements. Both the IR sensitive thermopile detector chip and the signal conditioning ASIC are integrated in the same TO-39 can. Integrated into the MLX90614 are a low noise amplifier, 17-bit ADC and powerful DSP unit thus achieving high accuracy and resolution of the thermometer. The thermometer comes factory calibrated with a digital SMBus output giving full access to the measured temperature in the complete temperature range(s) with a resolution of 0.02°C. The user can configure the digital output to be pulse width modulation (PWM). As a standard, the 10-bit PWM is configured to continuously transmit the measured temperature in range of -20 to 120°C, with an output resolution of 0.14°C.
  • Makerfire 10pcs Arduino NRF24L01+ 2.4GHz Wireless RF Transceiver Module New
    Brand New, 90 Days Warranty Model: NRF24L01
  • Comidox 4PCS MCP4725 Breakout Module I2C DAC 12Bit Development Board 2.7V to 5.5V Supply with EEPROM for Arduino Raspberry Pi
    The MCP4725 is a single-channel 12-bit buffered voltage output DAC with non-volatile memory (EEPROM) that allows you to store configuration register bits (2 bits) and DAC input data (12 bits) to non-volatile EEPROM (14-bit) In memory. The DAC can be configured for normal mode or power-saving shutdown mode by setting the configuration register bits. The DAC allows you to send analog signals, such as sine waves, from a digital source such as the I2C interface on an Arduino microcontroller. Digital to analog converters are ideal for sound generation, musical instruments and many other creative projects. This version of the CJMCU-MCP4725 Breakout solves some of the board's problems, including IC packages, I2C pinouts, changing the overall board size to better suit your project, and some minor adjustments. The board breaks down each pin you need to access and uses the MCP4725 (including GND and signal OUT pins) to connect to the oscilloscope or any other device you need to connect to the board. There are also SCL, SDA, VCC and another GND for the basic I2C pinout. The device can be used with a 2-wire I2C-compatible serial interface and is powered by a single supply from 2.7V to 5.5V. If you want more than one MCP4725 on the bus, you can disable the pull-up resistors on this board.
  • ELECROW Crowpi Raspberry Pi 4 3 b 3b+ 4b+ Kit Raspberry Pi Learning Programming Kit with Sensors - Advanced Version
    Raspberry Pi 4 Model B Starter Kit: Crowpi advanced version comes with Raspberry Pi 4. You can also use the raspberry pi 3 b 3b+ 2 and more on crowpi. Rasberry Pi Projects: With the sensors buttons and output devices all pre-wired in one package you can start doing projects instantly and easily with crowpi. Raspberry Pi Sensors: The Crowpi raspberry pi 4 programming kit is jam-packed with lots of buttons such as 19 different sensors in a tidy easy to use package. You don't have to wait and wire things. Build Quality: Solid ABS shell and well made components in one place make it strong and convenient to travel. Programming Lessons: This raspberry pi 4 learning kit ships with step by step instructions and provides 21 lessons to take you through identifying components reading code and running it in the terminal.
    303.00 $
  • Comidox 3Pcs MCP2515 CAN Bus Module TJA1050 Receiver SPI Module for Arduino 51 MCU ARM Controller Development Board
    Support CAN V2.0B technical specification, communication rate 1Mb/S. 0~8 bytes long data field, standard frame, extended frame and remote frame. Module 5V DC power supply, SPI interface protocol control, 120 ohm terminating resistor, impedance matching, guaranteed drive capability, long-distance data transmission to prevent signal emissions. Module size: 44mm x 28mm, centering distance of the positioning screw hole: 23mm x 38mm. Operating current: typical value 5mA, standby current 1 microamperes, except for the power indicator. Working temperature: industrial grade -40 ° C to 85 ° C.
    8.99 $
  • HiLetgo 5pcs IRF520 MOSFET Driver Module MOSFET Button Drive for Arduino MCU ARM Raspberry PI
    5pcs IRF520 MOSFET Driver Button Module Voltage: 3.3V, 5V Output load voltage: 0-24V Output load current: <5A (1A above need to add heat sink) Platform: Arduino, MCU, ARM, raspberry pie
    5.99 $
  • Grove I2C 4 Ch / 16 Bit Analog to Digital Converter for Raspberry Pi/Arduino / ESP8266
    Comes with open source drivers for the Raspberry Pi, ESP8266 and the Arduino 4 Channels of 16 bit Analog to Digital Conversion based on TI ADS1115 Works Perfectly with the Pi2Grover Grove Interface to the Raspberry Pi On board status LEDS for Power and I2C activity
    16.95 $
  • KEYESTUDIO 16-Channel 12-bit Servo Motor Driver Board I2C Interface for Arduino R3 Controller
    This expansion board can directly stack on the controller R3 board and can drive up to 16 servos Uses I2C input, just occupy A4 and A5 interface on the control board Contains PCB double sided holes, can direct to solder with components to build up prototyping circuits Servo power supply independent V + input up to 6V How to use: Search for "keyestudio wiki KS0258" in Google Chrome to get the wiki online tutorial for this product.
    10.99 $
  • REXQualis Most Complete Starter Kit Base on Arduino MEGA 2560 w/Detailed Tutorial Compatible with Arduino IDE
    REXQualis complete starter kit base on Arduino MEGA 2560 comes with more than 200pcs components, 67 kinds of components and sensors module. LCD1602 Module,MPU-6050 Module and RC522 RFID Module come with pin header, Motors come with wires, not need to solder by yourself. Include High Quality Base Board base on Arduino MEGA 2560 100% compatible with Arduino IED. Free PDF Tutorial and Datasheet are available to download from our official website or you can contact our customer service. All of the Components and Integrated Circuits are individually packaged and labeled, and packing in a plastic box which is bigger enough for you.
  • Keywish Project AE-01 Scratch Starter Kit for Arduino R3 Mega328 with 30 Lessons Tutorial Compatible with Arduino IDE Mixly Sctratch Mblock Graphical Programming
    Free PDF tutorial (30 lessons) Contains basic courses, sensor courses, comprehensive experimental courses from easy to difficult Support Arduino IDE, Mixly, mblock Scratch graphical programming. High quality kit with Development Board. 100% compatible with Arduino UNO R3 This is the most basic Arduino kit for the beginner, has all the component you need to start Arduino Tutorial Link:github.com/keywish/keywish-uno-starter-kit