Strategies: Arduino jsonarray example | Last places

  • Freenove RFID Starter Kit V2.0 with Board V4 (Compatible with Arduino IDE), 266-Page Detailed Tutorial, 198 Items, 49 Projects, Solderless Breadboard
    266-page detailed tutorials (including basic electronics and programming knowledge) -> The download link can be found on the product box. (No paper tutorial.) 198 common items -> All parts needed to complete the projects in the tutorial. No soldering required. 49 interesting projects -> Each project has circuit diagram and tested code with detailed explanation. Extra advanced projects -> Make virtual instruments (voltmeter, oscilloscope) and game consoles. Get support -> Our technical service team is always ready to answer your questions.
  • XCSOURCE 5pc Pro Mini Enhancement ATMEGA328P 16MHz 5V Compatible Arduino PRO Module TE362
    ATmega328 running at 16MHz with external resonator USB connection off board Supports auto-reset Max 150mA output Over current protected
  • DIYmall U R3 Development Board ATmega328P Microcontroller Compatible with Arduino,with Blue USB Cable
    1, U R3 board is very widely ranged used, it contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. 2, Microcontoller based on the ATmega328 3, the board is small but exquisite, it is a good choice for you to start your own DIY arduino projects. 4, link to buy DIYmall mega 2560: https://www.amazon.com/dp/B07YB6MMMS 5, What you will get is: 1 X DIYmall U R3 Dev.board, 1 X USB cable
  • Freenove Ultimate Starter Kit with Board V4 (Compatible with Arduino IDE), 273-Page Detailed Tutorial, 217 Items, 51 Projects, Solderless Breadboard
    273-page detailed tutorials (including basic electronics and programming knowledge) -> The download link can be found on the product box. (No paper tutorial.) 217 common items -> All parts needed to complete the projects in the tutorial. No soldering required. 51 interesting projects -> Each project has circuit diagram and tested code with detailed explanation. Extra advanced projects -> Make virtual instruments (voltmeter, oscilloscope) and game consoles. Get support -> Our technical service team is always ready to answer your questions.
    34.95 $
  • CAN-BUS Shield Compatible with Arduino and Seeeduino
    Implements CAN V2.0B at up to 1 Mb/s SPI Interface up to 10 MHz Standard (11 bit) and extended (29 bit) data and remote frames Two receive buffers with prioritized message storage Industrial standard 9 pin sub-D connector, Two LED indicators
    23.88 $
  • Keywish Project AE-01 Scratch Starter Kit for Arduino R3 Mega328 with 30 Lessons Tutorial Compatible with Arduino IDE Mixly Sctratch Mblock Graphical Programming
    Free PDF tutorial (30 lessons) Contains basic courses, sensor courses, comprehensive experimental courses from easy to difficult Support Arduino IDE, Mixly, mblock Scratch graphical programming. High quality kit with Development Board. 100% compatible with Arduino UNO R3 This is the most basic Arduino kit for the beginner, has all the component you need to start Arduino Tutorial Link:github.com/keywish/keywish-uno-starter-kit
    25.99 $
  • Aideepen Proto Screw Shield Assembled Terminal Point Prototype Expansion Board Opening Source Reset Button PCB Bareboard D13 Universal LED for Arduino
    【Can Plug the Screw Shield into the Arduino】It has pins on the bottom which correspond to the female connectors on an arduino so that you can plug this shield into the arduino. Once it's plugged in it's very secure very snugly fit so it doesn't come off very easily 【Can Stack Other Shields】It has female connectors on the top corresponding to those on the Arduino so that you are not losing those when you put the shield on it 【Easy to Fly Line Connection】It has those holes on the side which are also connected to the same connections here and normally you can't easily stick a write into these holes. However if you unscrew the corresponding screw on the top you can that insert a wire and then you screw the screw back in again and then it's very hard to get the wire out so this enables a secure connection to the Arduino 【Easy to Connection】Provide terminal for the Arduino IO, convenient port connection 【Can be used to Extension Plate】With Proto shields, can be used as a prototype extension plate in the middle
    9.99 $
  • Treedix Screw Terminal Block Breakout Board Moduleor Compatible with Arduino MEGA-2560 R3
    Terminal breakthrough module-for Arduino MEGA-2560, this product is not soldered and assembled, you need to solder and assemble it yourself after purchase. Terminal pitch 3.5mm / 0.138", wire size range from 26AWG to 16AWG, strip length 5mm, pin seat and cage copper. 3 pieces 3V and 4 pieces 5V, a total of 8 ground, can achieve more expansion. Compared with other products, the wiring terminals in this product do not need screws, which are simple to operate and directly inserted into the breakthrough board. Using the adapter module, you can easily extend the Arduino project to industrial control applications.
    19.99 $
  • ElectroCookie Proto Shield Kit Compatible with Arduino Mega R3, Stackable DIY Expansion Prototype PCB (2 Pack)
    Useful in creating your own DIY electronic projects 2 hole strips with power bus lines for quick and easy prototyping 15% larger than other other protoshields for extra components High-quality and Gold-plated finish to prevent oxidation, and all holes are through-plated for mounting strength Lead free and RoHS compliant, Environment-friendly
  • USB Data Sync Cable for Arduino UNO / Arduino Mega 2560 Rev 3 R3 Microcontroller
    ✔ USB Cable to connect an Arduino microcontroller to a PC or Mac ✔ Cable is 3ft (plug to plug) in length. The perfect size to allow mobility while connected to your Arduino device ✔ Compatibility tested with genuine Arduino UNO (A000066) / Arduino Mega 2560 (A000067) Rev 3 R3 Microcontroller Models ✔ Cable is also compatible with generic ATmega328P and ATmega2560 design based boards