Secrets: Arduino zs 042 example | Coupon code

  • Seeeduino XIAO The Smallest Arduino Microcontroller Based on SAMD21,with Rich Interfaces, 100% Arduino IDE Compatible, desiged for Projects Need Arduino Micro,3 pcs
    [ Powerful CPU] Seeeduino XIAO carries powerful CPU ARM Cortex-M0+ 32bit 48MHz microcontroller (SAMD21G18), which is three times than Arduino Uno and Arduino Nano. In addition, this Arduino IDE compatible board Xiao is also equipped with 256KB flash memory and 32KB SRAM. [Rich Interfaces in a Tiny Size] There is 14 GPIO PINs, which can be used for 11 analog PINs, 11 digital PINs, 1 I2C interface, 1 UART interface, and 1 SPI interface in such a tiny size - only 20mm*17.5mm ( as small as your thumb). Seeeduino XIAO development board is the smallest Arduino compatible board in the Seeeduino series. [Fully compatible with Arduino IDE] The Seeeduino XIAO development board is perfectly compatible with Arduino IDE, you can easily develop some small projects with the help of the large and comprehensive Arduino library. As it has a 2.54mm pin pitch, it is an Arduino microcontroller that can be used even when inserted into a breadboard. [USB Type C Support] Seeeduino XIAO supports the USB Type-C interface which can supply power and download code. There are power pads at the back of the XIAO which support battery and make it designed for wearable devices to become realistic. [Perfect for Wearable and Tiny Arduino Projects] On the other hand, this little board has good performance in processing but needs less power. As a matter of fact, it is designed in a tiny size and can be used for Arduino wearable devices and small projects.
  • DORHEA 4PCS ESP32 Development Board ESP-32S Microcontroller Processor Integrated Chip CP2102 WiFi NodeMCU-32S ESP-WROOM-32 Compatible with Ardu ino IDE
    Dual core ESP-32 development board, 2.4GHz Dual Mode Development Board. Ultra-Low power consumption,small volume, easy to embed to other products, works perfectly compatible with the Ardu ino IDE. ESP32 development board support lua program, easy to develop, support LWIP protocol, Freertos, three modes : AP, STA and AP + STA. ESP32 is a safe, reliable, and scalable to a variety of applications,the user can cut off the power of the CPU and use the low-power coprocessor to continuously monitor the status of the peripherals or whether some of the analog values ​​exceed the threshold.
  • HiLetgo 315Mhz RF Transmitter and Receiver Module link kit for Arduino/ARM/MCU/Raspberry pi
  • ELEGOO Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 (Nano x 3 Without Cable)
    The Nano is using the chips ATmega328P and CH340, not FT232 as official Arduino, so pls. use the driver from above link. It is a smallest, complete, and breadboard friendly board. It has everything that Diecimila/Duemilanove has (electrically) with more analog input pins and onboard +5V AREF jumper. Nano's got the breadboard-ability of the Boarduino and the Mini+USB with smaller footprint than either, so users have more breadboard space. It's got a pin layout that works well with the Mini or the Basic Stamp (TX, RX, ATN, GND on one top, power and ground on the other). The Nano can be powered via the Mini-B USB connection, 7-12V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source.
    15.99 $
  • REXQualis Board Base on Arduino UNO R3 ATmega328P ATMEGA16U2 with USB Cable Compatible with Arduino IDE Projects
    REXQualis R3 Board is 100% compatible with the Arduino IDE. REXQualis R3 Board uses an ATMega16U2 instead of the ATMega8U2 chip. Faster transfer rates and more memory. Control using ATMEL ATMEGA328P chip(the same with Arduino R3) Clear prints on the female header connector, more precise and easier to use the wire. Powered via the USB cable or power it with an AC-to-DC adapter or battery to.
    11.86 $
  • Nano V3.0, Nano Board ATmega328P 5V 16M Micro-Controller Board Compatible with Arduino IDE (Nano x 3 with USB Cable)
    Original ATmega328P CH340 chip is used. Improved new version CH340G Replace FT232RL. LAFVIN Nano V3.0 card is 100% compatible with the Nano card, and fully compatible with Windows, Mac and Linux operating system. Works the same as original Nano, runs perfectly on programming software. Using Atmel Atmega328P-AU MCU, Support ISP download; Support USB download and Power. LAFVIN Nano CH340 controller is a compact board similar to the R3 board, smaller and breadboard-friendly than Diecimila.
    13.99 $
  • Cylewet 10Pcs Cylindrical Electret Condenser Microphone Pickup with 2 Pins 9×7mm for Arduino (Pack of 10) CYT1013
    Diameter: 9mm/ 0.35inches<br> Length: 7mm/ 0.28inches<br> Sensitivity: -48-66dB<br> Frequency Range: 50 20KHz<br> Current Consumption: Max 500uA<br>
    5.99 $
  • HiLetgo GY-906 MLX90614ESF Non-contact Infrared Temperature Sensor Module IIC I2C Serial for Arduino
    MLX90614 is an infrared thermometer for non-contact temperature measurements. Both the IR sensitive thermopile detector chip and the signal conditioning ASIC are integrated in the same TO-39 can. Integrated into the MLX90614 are a low noise amplifier, 17-bit ADC and powerful DSP unit thus achieving high accuracy and resolution of the thermometer. The thermometer comes factory calibrated with a digital SMBus output giving full access to the measured temperature in the complete temperature range(s) with a resolution of 0.02°C. The user can configure the digital output to be pulse width modulation (PWM). As a standard, the 10-bit PWM is configured to continuously transmit the measured temperature in range of -20 to 120°C, with an output resolution of 0.14°C.
    14.99 $
  • Arduino MKR Zero with Headers [ABX00012]
    The Central Board for your Electronic Project Powerful 32-bit Microcontroller and Micro SD Memory Card Connector Ideal for: Music, Audio processing, robotics, art installations Part of the Arduino Maker Board Family for IoT Devices, easy to configure with Arduino Software.
  • AITRIP 3pcs for Arduino Mini Nano V3.0 ATmega328P 5V 16M Micro Controller Board Module with 3pcs USB Cable for ArduinoIDE
    *The Nano is using the chips ATmega328P and CH340, Replace FT232RL. *It is a smallest, complete, and breadboard friendly board. It has everything that Diecimila/Duemilanove has (electrically) with more analog input pins and onboard +5V AREF jumper. *Nano's got the breadboard-ability of the Boarduino and the Mini+USB with smaller footprint than either, so users have more breadboard space. It's got a pin layout that works well with the Mini or the Basic Stamp (TX, RX, ATN, GND on one top, power and ground on the other). *The Nano can be powered via the Mini-B USB connection, 7-12V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source. *Arduino Nano V3.0 ATMEGA328P Improved version with 3pcs pin headers (2pcs 15pin headers +1pcs 6pin headers).