Responses: Arduino robot motor driver | Test & Recommendation

  • HiLetgo 2pcs PCA9685 16 Channel 12-Bit PWM Servo Motor Driver IIC Module for Arduino Robot
    Communication Interface: IIC 16-way steering gear control Voltage: DC5-10V power supply The PCA9685 chip is wrapped in the center of the board All PWM output lines have a 220 ohm series resistor protection and can easily drive LED.
  • HiLetgo PCA9685 16 Channel 12-Bit PWM Servo Motor Driver IIC Module for Arduino Robot
    Communication Interface: IIC 16-way steering gear control Voltage: DC5-10V power supply The PCA9685 chip is wrapped in the center of the board All PWM output lines have a 220 ohm series resistor protection and can easily drive LED
  • Onyehn 16 Channel PWM Servo Motor Driver PCA9685 IIC Module 12-Bit for Arduino Robot or Raspberry pi(Pack of 3pcs)
    Communication Interface: IIC. It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages). 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs. Adjustable frequency PWM up to about 1.6 KHz;Configurable push-pull or open-drain outputManufacturer. 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate.
  • DAOKI 2 PCS L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560 with Dupont Cable
    The signal is shown in the figure The connecting method is shown inbelow figure after enable ENA ENB Driving DC motor Because the module is drived by double H bridge,it can drive two motors simultaneously. Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled Package Content: 2 x L298N Motor Drive Controller Board, 1 x 11.8" male-FeMale Dupont Cables 12 PIN, 1 x 11.8" Male-Male Dupont Cables 12 PIN, 1 x 19.6" 28AWG Wire
    6.99 $
  • 4Pack L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560
    Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability,low calorific value and strong anti-interference ability. This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage of the voltage stabilizing chip,please use an external 5V logic supply when using more than 12V driving voltage. Using large capacity filter capacitor,this module can follow current to protect diodes,and improve the reliability. Dual-channel H-bridge driver working mode creates higher working efficiency To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage
    9.79 $
  • HiLetgo 2pcs A3967 Stepper Motor Drive Board EasyDriver Stepper Motor Driver for Arduino Raspberry Pi Robot
    The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor. The EasyDriver has an on board voltage regulator for the digital interface that can be set to 5V or 3.3V. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control. EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors.
    6.79 $
  • LM YN Motor Stepper Servo Robot Shield v2 with PWM Driver Shield for Arduino
    We have upgraded the shield kit to make the bestest, easiest way to drive DC and Stepper motors. This shield will make quick work of your next robotics project! We kept the ability to drive up to 4 DC motors or 2 stepper motors, but added many improvements.<br> Instead of a L293D darlington driver, we now have the TB6612 MOSFET driver: with 1.2A per channel and 3A peak current capability. It also has much lower voltage drops across the motor so you get more torque out of your batteries, and there are built-in flyback diodes as well.<br> Instead of using a latch and the Arduino's PWM pins, we have a fully-dedicated PWM driver chip onboard. This chip handles all the motor and speed controls over I2C. Only two pins (SDA & SCL) are required to drive the multiple motors, and since it's I2C you can also connect any other I2C devices or shields to the same pins. This also makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3.<br> Completely stackable design: 5 address-select pins means up to 32 stackable shields: that's 64 steppers or 128 DC motors! What on earth could you do with that many steppers? I have no idea but if you come up with something send us a photo because that would be a pretty glorious project.<br> Lots of other little improvements such as a polarity protection FET on the power pins and a bit of prototyping area. And the shield is assembled and tested here at Adafruit so all you have to do is solder on straight or stacking headers and the terminal blocks.<br>
    16.99 $
  • HiLetgo TB6612 Mosfet for Arduino Motor Shield Standard IIC I2C TB6612FNG Stepper Motor PCA9685 PWM Servo Driver Shield V2 Robot PWM Uno Mega R3 Replace L293D
    H-Bridges: TB6612 chipset provides 1.2A per bridge (3A peak) Chip: TB6612FNG motor driver chip Completely stackable design: 5 address-select pins means up to 32 stackable shields Characteristic: Arduino interface is fully compatible expansion Feature: Motors automatically disabled on power-up
    11.99 $
  • KeeYees 5pcs SG90 9G Micro Servo Motor with PCA9685 16 Channel 12 Bit PWM Servo Motor Driver IIC Module for Arduino for Raspberry Pi RC Robot Helicopter Airplane Remote Control
    【Package】This is a great useful kit for DIY, which contains with 5pcs SG90 9G Micro Servo Motors and 12 Bit PWM Servo Motor Driver. 【SG90 Micro Servo】Operating speed: 0.12second/ 60degree (4.8V no load); Stall Torque (4.8V): 17.5oz /in (1kg/cm); Operating voltage: 3.0V~7.2V; Dead band width: 7usec. 【PCA9685 Servo Motor Driver】It is a 16-way steering gear control; Communication Interface: IIC; Voltage: DC5-10V power supply; All PWM output lines have a 220 ohm series resistor protection and can easily drive LED.
  • Qunqi L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper For Arduino
    Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip.Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability High working power to 35v,large current can reach 3A MAX and continue current is 2A, power to 25w. Large capacity filter capacitance,afterflow protection diode, more stable and reliable.