From A to Z: Arduino robot motor driver | Complete Test

  • Ximimark PCA9685 16 Channel 12-Bit PWM Servo Motor Driver IIC Module for Arduino Robot,2Pcs
    Using I2C communication, built in PWM driver and a clock. Green power indicator lamp. 16-way steering gear control. Includes reverse polarity protection on the input board. Using only two pins, control 16 free-running PWM outputs. All PWM output lines have a 220 ohm series resistor protection and can easily drive LED.
  • HiLetgo 2pcs A3967 Stepper Motor Drive Board EasyDriver Stepper Motor Driver for Arduino Raspberry Pi Robot
    The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor. The EasyDriver has an on board voltage regulator for the digital interface that can be set to 5V or 3.3V. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control. EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors.
  • HiLetgo 2pcs PCA9685 16 Channel 12-Bit PWM Servo Motor Driver IIC Module for Arduino Robot
    Communication Interface: IIC 16-way steering gear control Voltage: DC5-10V power supply The PCA9685 chip is wrapped in the center of the board All PWM output lines have a 220 ohm series resistor protection and can easily drive LED.
  • HiLetgo PCA9685 16 Channel 12-Bit PWM Servo Motor Driver IIC Module for Arduino Robot
    Communication Interface: IIC 16-way steering gear control Voltage: DC5-10V power supply The PCA9685 chip is wrapped in the center of the board All PWM output lines have a 220 ohm series resistor protection and can easily drive LED
    6.99 $
  • ALAMSCN 6PCS L298N Motor Driver Controller Board Module DC Motors Dual H-Bridge with Jumper Wires Kit for Arduino Smart Car Robot Power UNO MEGA R3
    This is a good Motor Drive for an Arduino and raspberry pi based RC car project. It comes with 6pcs motor drive modules and 60pcs jumper wires for different interfaces, which can meet your project needs. Motor Drive Controller: L298N used as the main driver chip. It has the strong driving ability, low calorific value and strong anti-interference ability. Jumper Wire Kit: 20cm Jumpers, Female to Female, Male to Male, Male to Female each 20Pin. NOTE: Suitable for DC motors in smaller projects, but not for prototyping. Not recommended for stepper motors.
    14.99 $
  • Designing Embedded Systems with Arduino: A Fundamental Technology for Makers
    94.42 $ 179.99 $ -48%
  • DAOKI 5 PCS L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560
    The signal is shown in the figure The connecting method is shown inbelow figure after enable ENA ENB Driving DC motor Because the module is drived by double H bridge,it can drive two motors simultaneously. Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled Package Included - 5 pcs L298N Motor Driver Controller Board Modules.
    13.99 $
  • Onyehn 16 Channel PWM Servo Motor Driver PCA9685 IIC Module 12-Bit for Arduino Robot or Raspberry pi(Pack of 3pcs)
    Communication Interface: IIC. It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages). 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs. Adjustable frequency PWM up to about 1.6 KHz;Configurable push-pull or open-drain outputManufacturer. 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate.
    12.99 $
  • PCA9685 16 CH 12Bit PWM Servo Motor Driver Board Controller IIC Interface for Arduino Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+ and Robot (2pcs)
    Contains an I2C-controlled PWM driver with a built-in clock. It means, unlike the TLC5940 family, you do not need to continuously send it signals tying up your microcontroller; it's completely free running! 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs, which is good when you want to control white or blue LEDs with a 3.4V+ forward voltage Supports using only two pins to control 16 free-running PWM outputs – you can even chain up 62 breakouts to control up to 992 PWM outputs. 3 pin connectors in 4 groups, so you can plug in 16 servos at one time (Servo plugs are slightly wider than 0.1" so you can only stack 4 adjacent ones on 0.1"-hole female headers. 12-bit resolution for each output - for servos, that means about 4us resolution at an update rate of 60Hz.
  • KeeYees 5pcs SG90 9G Micro Servo Motor with PCA9685 16 Channel 12 Bit PWM Servo Motor Driver IIC Module for Arduino for Raspberry Pi RC Robot Helicopter Airplane Remote Control
    【Package】This is a great useful kit for DIY, which contains with 5pcs SG90 9G Micro Servo Motors and 12 Bit PWM Servo Motor Driver. 【SG90 Micro Servo】Operating speed: 0.12second/ 60degree (4.8V no load); Stall Torque (4.8V): 17.5oz /in (1kg/cm); Operating voltage: 3.0V~7.2V; Dead band width: 7usec. 【PCA9685 Servo Motor Driver】It is a 16-way steering gear control; Communication Interface: IIC; Voltage: DC5-10V power supply; All PWM output lines have a 220 ohm series resistor protection and can easily drive LED.