For Dummies: Arduino example led blink | Customer Evaluation

  • Getting Started with Arduino: The Open Source Electronics Prototyping Platform (Make)
    Maker Media Inc
  • HiLetgo 3pcs ESP8266 NodeMCU CP2102 ESP-12E Development Board Open Source Serial Module Works Great for Arduino IDE/Micropython (Large)
    ESP8266 CP2102 NodeMCU LUA ESP-12E WIFI Serial Wireless Module Built-in Micro-USB, with flash and reset switches, easy to program Arduino compatible, works great with the latest Arduino IDE/Mongoose IoT/Micropython
  • eBoot 30 Pieces Photoresistor Photo Light Sensitive Resistor Light Dependent Resistor 5 mm GM5539 5539
    Quantity: 30 x photoresistor, 5 mm GM5539 resistor Maximum voltage: 150 Volt DC Maximum wattage: 100 mW; Spectral peak: 540 nm Light resistance (10 Lux): 50-100 Kohm; Operating temperature: - 30 ~ + 70 degree Celsius Enough photo light sensitive resistors are handy for your DIY and hand working projects
  • PI-TOP [4 Sensor Foundation Kit with 14 Programmable Components - LEDs, Ultrasonic Sensor, Light Sensor, Sound Sensor and Lego Connectors. Compatible [4], Grove and Raspberry Pi
    DESIGN, CODE & MAKE: The pi-top [4] Sensor Foundation Kit contains everything you need to start coding and making with electronics. Connect the included Foundation Plate to your pi-top [4] (sold separately) and attach LEDs, sensors and buttons to make amazing inventions. 100+ HOURS OF PROJECTS: Explore our project library to learn to code and create anything from a musical instrument to the ultimate alarm system. Our step by step tutorials will help you write code to control the electronic components that come with the kit. pi-top [4] (sold separately) is needed to complete the tutorials ADD SMARTS TO LEGO CONSTRUCTIONS: LEGO connectors allow you to integrate electronic components into your LEGO builds, and write code to control them, so you can design, code and make anything you can imagine. PLUG & PLAY: Dock the Foundation Plate that comes in the kit onto your pi-top [4] or pi-top [4] DIY Edition (sold separately). Plug components into the Foundation Plate and get started right away, following step-by-step tutorials to learn the basics of coding and physical computing. WHAT’S IN THE BOX: the pi-top [4] Sensor Foundation Kit comes with a Foundation Plate to connect components to a pi-top [4], 2 green LEDs, 2 yellow LEDs, 2 red LEDs, an ultrasonic sensor, 2 buttons, 2 potentiometers, a light sensor, a sound sensor, 8 LEGO connectors, connecting cables, 1-year warranty and friendly customer service. pi-top [4] not included.
    79.95 $
  • HiLetgo 3pcs GY-302 BH1750 BH1750FVI Light Intensity Illumination Module for arduino
    HiLetgo 3pcs GY-302 BH1750 Light Intensity Illumination Module Model: GY-302 Dimensions: 13.9mm X 18.5mm Original BH1750FVI chip using ROHM Power supply :3-5v
    6.69 $
  • HiLetgo ESP-WROOM-32 ESP32 ESP-32S Development Board 2.4GHz Dual-Mode WiFi + Bluetooth Dual Cores Microcontroller Processor Integrated with Antenna RF AMP Filter AP STA for Arduino IDE
    2.4GHz Dual Mode WiFi + Bluetooth Development Board Ultra-Low power consumption, works perfectly with the Arduino IDE Support LWIP protocol, Freertos SupportThree Modes: AP, STA, and AP+STA ESP32 is a safe, reliable, and scalable to a variety of applications
    10.99 $
  • KeeYees Development Board WiFi WLAN Wireless Module for ESP8266 for NodeMCU for ESP-12E for Arduino (3pc)
    The controllers are easy to program by using the CP2102-USB interface without having to press the flash and reset buttons before each flash operation. The development board has integrating GPIO, PWM, IIC, 1-Wire and ADC all in one board. Support smart link smart networking. The fast and affordable technology for WiFi. Make your development the fastest way combined with firmware for NodeMcu. Modern, state-of-the-art LUA technology. It is an integrated unit with all available resources on board. It's very easy for Arduino projects or any development board with I / O pins. Modern Internet development tools can use the built-in API to instantly put your idea on the fast track.
    11.99 $ 12.99 $ -8%
  • Gowoops 10 PCS of Digital Light Intensity Detection Photosensitive Sensor Module for Arduino
    1. Using the sensitive type photosensitive resistance sensor 2. The comparator output signal clean waveform is good, driving ability, than 15mA. 3. With adjustable potentiometer can adjust the brightness of the light detected 4. Working voltage 3.3V-5V, the output format: Digital switching output (0 and 1) 5. With bolt holes for easy installation, a small board PCB size: 3.2cm x 1.4cm, using a wide voltage LM393 comparator
    14.99 $
  • Gikfun Infrared Diode Led IR Emission and Receiver for Arduino (Pack of 10 Pairs) EK8460
    10PCS VS1838B Infrared receiver and 10PCS 5mm 940nm IR infrared Emission Tube LED Lamp The ir receiver is a small design with a built-in dedicated IC that is highly resistant to interference and can withstand environmental interference. The infrared diode's pin is not easy to be oxidized, it is easy to be tinned, and the solderability is good; Long service life, no red storm, high reliability Suitable for infrared products such as electronic toy remote control, infrared camera, infrared temperature measurement, etc.
  • DIYmall 5 Pack HC-SR501 Pir Motion IR Sensor Body Module Infrared for Arduino
    Use Potentiometer 105, output timing is from 0.5S to 200S. Same product link https://www.amazon.com/dp/B07CSM3K63 NOTE: On this retrigger jumper is a solder jumper, and you need solder it by yourself Pls note that there is no IR emitter in this module, the principle of PIR sensor is to detect the infrared radiation emitted by the human body, it only have a IR sensor (cell) Package Included: 5 X HC-SR501 PIR Infared Sensor. If any question, pls contact us by email. You can find " Sold by DIYmall" under Buy Now button, click "DIYmall" and you will get to a new page, click "Ask a question".