Explanation: Auto leveling 3d printer | Technical sheet

  • Creality BL Touch 3D Printer Upgraded Auto Bed Leveling Sensor Kit for Cr-10 /Ender 3 /Ender 3Pro /Ender 5 /Ender 5Pro /CR 10S /CR-10 S4/S5/CR 20 /20Pro
    【Awesome BLTouch Upgraded Kit】Unlike the inductive probe, Our Creality BLTouch auto bed leveling kit was a touch-based 3D printer bed leveling probe which enables automatic bed leveling on your 3D printer, regardless of print surface. This touch sensor works perfectly with any surface, from glass to blue tape or woods, metals and so on. 【Widely Application】Suitable for Ender-3 / Ender-3s / Ender-3 Pro / Ender 5 / Ender 5 Pro/ CR-10 / CR-10S / CR 10S4 / CR 10S5 / CR-20 / CR-20 Pro. (NOTE: Can't use for Ender 3V2, CR-10V2, CR-10 V3, CR 10S Pro) Please flash the firmware first. Use the ISP cable to flash the firmware for V1 mainboard. Use USB cable to flash for V2 Mainboard. If you have a V 4.2.2 mainboard, please download the instruction from here: https://m.media-amazon.com/images/I/C1i4W82Kq+S.pdf 【Firmware】Please move to the Creality Official Website to download the firmware and flash it at first, For V1 mainboard, use isp to flash of V1.1.4 or V1.1.5 (8 bit) mainboard; For V4 mainboard, use SD to flash the new Version V4.2.2 or V4.2.7(32 bit) mainboard; For V2 mainboard, use USB to flash,The circuit wiring of CR-10S/CR-10S4/CR-10S5/CR 20 are different from the manual. 【High-precision】 BLTouch’s Standard Deviation in repeatability is around 0.005mm, at that precise.BLTouch is an auto leveling sensor for 3D Printers that can precisely measure the tilt of Bed surface. It could work with any kinds of bed materials, such as glasses, woods, metals, and so on. 【Genuine High Quality Set】Our package was included 1 set of auto bed Leveling Kit and an another replacement probe. Simple, smart and easy to install.If you encounter unsolvable problems during installation and use, please feel free to contact us, our after-sales technical team will provide you with detailed solutions within 24 hours.
  • ANYCUBIC Chiron 3D Printer, Semi-auto Leveling Large FDM Printer with Ultrabase Heatbed, Suitable for 1.75 mm Filament, TPU, Hips, PLA, ABS etc. / 15.75 x 15.75 x 17.72 inch (400 x 400 x 450mm)
    Extra Large Build Volume, ANYCUBIC Chiron 3D Printer comes with one of the largest build volume of 15.75 x 15.75 x 17.72 inches, you can print models that 90% of other printers could not, The unique high precision nozzle of 0.4mm hot end with straight through design reduces the weight on the X axis which delivers better performance even on very tall prints, Your creativity will be maximized Semi Auto Leveling and Resume Print, Equipped with an auto leveling module which automatically detects 25 points, supports real time adjustment compensation of nozzle height, Chiron 3D Printer can resume printing after power outage or any other unexpected stoppage, One click to resume from the last recorded position when suffering power outages, And the sensor pauses prints and sets off an alarm when you run out of filament which greatly saves time and material Easy to Assemble and Use, Full metal body, stable and durable, modular design and only take 5-10 minutes to assemble, TFT Touch Screen with brand new friendly UI to preview model and printing process on screen, offline printing, We use high grade Titan Extruder, smooth feeding and not easy to plug, which can provide you a better printing experience of flexibility Printing Precise and Safe, Equipped with Y Axis Dual Sideway and Z axis dual screw rod design, the height on both sides of the Z axis will be recalibrated before each printing which can reduce the probability of releveling before each printing and our Chiron 3D Printer’s print precision is greatly improved, 24V DC high power heated bed, heating up to 100℃, Independent high-power mosfet drive, taking into account safety and heating effect More Function, Ultrabase Pro, Coated with a special composite coating make the printed large model not easy to warp and easy to demold, All ANYCUBIC 3D printers backed with lifetime technical support and 24 hours professional customer service
  • 3D Printer, LABISTS Auto Leveling 3D Printer DIY Kit for Adults with Resume Printing Function, Touch Screen, Filament Detection, Printing Size 220X220X250mm
    【Auto Leveling 3D Printer】 High-precision leveling detector with matrix automatic leveling function frees you from bed leveling troubles. Finish data collection of 25 points within 5 minutes for automatic calibration. 【Resume Print Function】 LABISTS 3D printer can resume printing from the last recorded extruder position after suffering unexpected power failure or PLA filament outage, saving time and avoiding waste. 【Filament Detection Prompt】 When the filament detector detects that PLA filament is broken or runs out, the system automatically pauses printing and prompts for feeding. One-button automatically feeds and unloads filament with a touch screen. 【Fast Assembly】 LABISTS 3D printer comes with several assembled parts, install the bracket, the nozzle, connect few cables, only 3 steps to easily finish assembly for even beginners in just 5 minutes. 【Widely Compatibility】 LABISTS 3D printer supports PLA, ABS and HIPS filament, compatible with Windows * Mac systems, also supports TF Card & USB cable connection.
  • Anet ET5X DIY 3D Printer, Auto Leveling with Resume Printing Function, 3.5 Inch LCD Color Touch Screen, Upgraded Over-Current Protection Mainboard, Large Size 11.8x11.8x15.7Inch
    📌【Ultra Large Print&Matrix Automatic Levelling】 300x300x400mm ultra large print volume. Auto measures 25 points across the print platform for heat bed leveling. An induction sensor can probe the bed in a grid and apply mesh-based compensation that ensures you print on a level bed every time, all without the time-consuming and labor-intensive leveling tasks. 📌【Filament Sensor&Power Outage Recovery】 The filament sensor detects the filament end and sends reminders to the screen to avoid air-printing. Resume printing and recover from exactly where it left off. No worries about unexpected power outages. 📌【Auto Filament Assignment&Assembled In No Time】 Automatic load and unload the filament with just a click.Pre-assembly and modular design with quick assemble in 10min. Solid Wire Connection,Distributor connector for solid wire connections. 📌【Dual Z-axis, More Accurate Print&Stable Y-axis Movement】 ET5 applies dual Z-axis rods and motors to make sure the smooth and accuracy of every slight movement. Dual Y axis guideway for a more stable and level moving stage of the build platform. Intuitive Touchscreen.Colorful LCD touch screen, allowing you to control the movement of X/Y/Z axis, leveling and printing with ease. 📌【Safe Designed Control Board】 You can connect your ET5 online or offline to any configuration for your convenience. You could print via SD card or USB flash drive. Self-developed industrial-grade 32bit control board with MCU STMF407. Stable operation with high precision. The mother board has thermal runaway protection. If the printer fails to detect the temperature for a certain time, it would automatically power off.
    279.89 $
  • Creality Upgraded BLTouch Auto Bed Leveling Sensor Kit for Ender-3/3S,Ender-3 Pro, Ender 5,Ender 5 Plus, CR-10,CR 10S, CR-20, CR-20 Pro 3D Printer
    Application: Suitable for Ender-3/Ender-3s /Ender-3 Pro/Ender 5/Ender 5 Plus/CR-10 /CR-10S/CR 10S4/CR 10S5/CR-20 /CR-20 Pro and so on 3D Printer. NOTE: (1) It doesn't fit CR-10 V2, CR-10 V3, CR 10S Pro; (2) If your Ender 3/3 Pro/5 Motherboard is V1.1.4/V1.1.5, need to use ISP Cable to flash firmware according the instruction. If your Ender 3/3 Pro/5 Motherboard is V4.2.2/V4.2.7, just use the SD card to flash firmware. Easy to Use: [ V3.1 BLTouch Sensor ] BLTouch is an auto leveling sensor for 3D Printers based on open-source,easy to use because it is small and simple. Since BLTouch can use the automatic bed level sensor as usual, gathering information and setting up the firmware will be easy. NOTE: Please make sure your account is allowed to receive messages. If you find there is no message and firmware from us, please contact us. Intelligence, self - check and alarm. Function of auto leveling is adopted to make it easier to use and to increase the success rate of shaping. High Precision: BLTouch standard deviation repetition accuracy is about 0.005mm. Package: 1 x BLTouch ,1 x Connector ,1 x Tie ,1 x Rack ,1 x M3X8 ,1 x Pinboard A ,1 x M3X6 ,1 x ISP ,1 x Pinboard,1 x Burner.
    54.99 $
  • Creality CR-6 SE Leveling-Free Starter FDM 3D Printer, Auto Bed Leveling, Five-Minute Assembly, TMC2209 Drivers, Enhanced Heatsink and Extruder, 4.3 Inch Touchscreen, Build Volume 235 x 235 x 250mm
    Ease of Use: Five-minute assembly, plus with an auto bed leveling system, the CR-6 SE brings you an unrivaled out of box experience. A Quiet Beast: 32-bit silent motherboard, Atmega2560 control chip, and 24V 350W MeanWell power supply enables the CR-6 SE to heat up quickly and consistently with reduced noise. Pro Performance: robust aluminum frame, dual lead screws and adjustable timing belt contribute to delivering a smoother print finish of the prints. Quality of Life Addons: Flexible hotbed clips, foldable filament holder for easy storage, stepper motor covers deliver a cleaner look. Smooth Printing Experience: The Newly-Designed Extruder on the CR-6 SE allows for a quick and painless filament feeding and the carborundum glass bed for better adhesion and easier removal, together with the filament run-out sensor and resume printing function will keep you printing, not troubleshooting problems.
    429.00 $
  • Creality CR-10S Pro V2 3D Printer with BL Touch Auto-Level Touch Screen Large Build Volume 300mmx300mmx400mm with Capricorn PTFE 95% Pre-Assembled 3D Printer
    Upgraded Silent Motherboard: CR-10S Pro V2 adopts V2.4.1 independently developed silent motherboard, which demonstrates firm properties as well as reduces noise. BLTOUCH AUTO LEVELING: Matrix Automatic Leveling, quality Bill Touch automatic leveling device.And the CR-10 Pro V2 will automatically measure the height of 9 unique points on the heated bed to determine the ideal settings for perfect prints every time. More Smoothly Printing: With Imported high-temperature resistant blue Teflon tube ensure great printing texture, and Bondtech Gear extrusion Structure has two high-density gear and big extrusion force for smooth feeding. Filament Sensor: Creality CR-10S Pro V2 3d printer has a newly-added innovative material shortage detection switch, Even also highly sensitive to detect transparent materials. Service: We provide lifetime unconditional technical supports, one year warranty free change and replace parts if any defects and missed and 24 hours customer service.
    626.00 $
  • EcubMaker TOYDIY 4-in-1 3D Printer(3D Dual Color Printing/Laser Engraving/CNC Carving) Easy to Use Entry-Level 180x180x180mm Auto Leveling (3D Printing+ Laser+ CNC)
    TOYDIY has FDM 3D printing, dual-color 3D printing, CNC engraving and laser engraving four functions. It can be quickly replaced in 30 seconds. TOYDIY has 180*180*180mm work space, no assembly required, that delivers users out-of-the-box experience. 3D Printing supports PLA filament, TOYDIY can realize full-automatic leveling. Three-layers heated bendable buildplate and the soft magnetic plate can easily remove the model. FDM-Dual Toolhead supports dual-color 3D printing of PLA filaments with two different colors. Laser engraving uses a 1500mW high-power laser, it can carve the surface of wood, plastic, leather and other materials. CNC engraving adopts 10000RPM 385 DC motor, it can engrave wood, acrylic, plastic and other materials, and supports relief engraving. TOYDIY 4-in-1 special software EcubWare supports the set up and slicing of four Toolheads without the need for additional dedicated software. After changed the Toolhead, can automatically recognize the corresponding print file. First-time users can get started very easily. EcubWare supports the above win7.64bit OS, and will support MAC system in the future.
    599.00 $
  • WEEDO X40 Independent Dual Extruder 3D Printer with 32-bit Silent Mainboard,4.3“Touch Screen, Auto-Leveling, Filament Runout Detection Build Volume 300x300x400mm,Supported Materials PLA/ABS/TPU/PVA.
    【Independent Dual Extruders】WEEDO X40 is designed with independent dual extruders that supports 5 printing modes: Normal single nozzle printing;Dual-color printing with the same material (PLA+PLA, ABS+ABS);Duplication mode printing (printing 2 copies of the same item at the same time);Mirror mode printing (printing a normal and a mirror copy of an item at the same time);Mixed material printing (PLA+PVA, ABS+PVA, PLA+TPU, ABS+TPU). 【Printing Reliability】WEEDO IDEX X40 is designed with filament runout detection to improve the overall printing reliability. We have also added essential quality of life features such as print resume after power loss and auto bed leveling that levels the bed before each print to ensure a perfect first layer every time. 【User Friendly UI System】WEEDO X40 adopts a 4.3-inch full-color touch screen.The user-friendly UI is equipped with a multi-language interface. Can’t remember what you named your .gcode? Don’t worry! The graphical print interface displays a preview picture and details for each model, making it easy to identify your file. 【Wi-Fi Function 】WEEDO X40 equipped with ESP32 Wi-Fi chip and a built-in camera module that allows you to check your printer while you are away. You can also start prints over the network with CURA and our Wiibuilder slicer integrations.When 40X connect to our control App: PoloPrint Pro,you’ll be able to receive notifications from your social account when prints are complete. 【Help Button & Warranty】The UI includes a context based Help icon, which is convenient for beginners to quickly get guidance on how to use the interface based on where they are on the menu. The additional designed FAQ and Error Diagnosis can be used to quickly analyze and resolve issues. One-year warranty for the printer and a 3-month warranty for the extruder. Lifetime technical support, any problems please feel free to contact our support team.
  • Eryone 3D Printer ER 20, Auto-Leveling Bed Sensor, Super Quiet 3D Printer with TMC2209, Powerful 32Bit Motherboard, 250 220 200mm
    <p><b>Easy to Use</b>: Auto-bed leveling gives you the perfect first layer and the ink coating glass makes you stick and remove printed objects easily.</p> <p><b>Silent</b>: TMC2209 offers whisper quiet and more accurate printing without the need of mechanical limit switch (sensorless).</p> <p><b>Simplicity</b>: Modular design, built-in power supply, auto bed leveling sensor, no bed adjust knob, plug and play. ER20‘s sleek & streamlined round corners comply with the ergonomic design.</p> <p><b>Reliable</b>: ER20 supplies resume printing, sparing you the unexpected head-scratching outage. Fully upgraded aluminum profile frame provides durability. The reliable extruder is mounted with an Eryone sensor for hassle-free printing.</p> Power failure resume feature: ER20 support the power failure resume feature. When the power system resume, the printer can resume the print.