Discover: Arduino default programming language | Discount code

  • SparkFun ESP8266 Thing Starter Kit for Internet of Things WiFi Development Includes headers jumper wires breadboard Serial breakout Mico-B USB Cable and LEDs Use to Start a Project or Learn IoT
    Beginner kit for wireless ESP8266 Thing. Program on Arduino IDE platform or Espressif IDF platform All module pins broken out for ease of use 802.11 b/g/n Wi-Fi Direct (P2P), soft-AP Integrated TCP/IP protocol stack Integrated low power 32-bit CPU could be used as application processor On-board LiPo charger/power supply No need to come up with a power solution
  • Arduino MKR WiFi 1010 [ABX00023]
    MKR 1010 simplifies the prototyping of WiFi-based IoT applications, easily connected and configured to other Arduino products. You do not need to be a network expert! The hybrid WiFi / BLE connectivity module has a low power consumption mode, improving the life of your batteries. Ideal for: Entry point to and professional IoT, building wireless sensor networks in minutes, remotely operated devices. Cloud features: the board can connect to any kind of existing WiFi network, or use it to create your own Arduino Access Point. It is also possible to connect your board to different Cloud services, including Arduino IoT cloud! Simply to power with a USB cable or external Li-Po 3.7V battery. Recharge the battery through the USB port.
  • SparkFun Qwiic Motor Driver I2C Plug and Play Breakout No Soldering required to control small DC Motors 1.2A Steady state drive per channel 1.5A Peak 2 channels 127 levels of drive strength 3.3V Logic
    4245 PSOC and 2-channel motor ports as the SCMD. 3 to 11 Volts VCC with 12V absolute max. Designed to communicate over I2C to make setting up your next robotic project fast and easy. Or control over TTL UART signals. Several I2C addresses, default UART bauds available. No soldering is required. Includes 2 Qwiic Connectors and screw terminals for motor and power hookup Direction inversion on a per motor basis. Thermal conduction area for attaching 3 small heat shrinks
  • CANADUINO PLC MEGA328 Programmable Logic Controller Electronics DIY Kit for Arduino Nano (Included)
    Build your own Powerful PLC (Programmable Logic Controller) with Arduino NANO V3 4 analog inputs || 4 analog outputs 0-10V || I2C bus for sensors, displays etc. 4 digital inputs 3.3 - 12V || 6 digital relay outputs 5A || RTC with battery backup A microcontroller module, compatible with Arduino NANO, is included. A power supply 12V DC (11-15V max.) >500mA is required.
    23.49 $
  • ACROBOTIC 4-Pack ESP8266 ESP-01 Breakout Board Breadboard Adapter for Arduino Raspberry Pi Programming ESP01
    Breadboard Breakout Board for the popular ESP-01 ESP-01S WiFi module for the ESP8266 (https://www.amazon.com/dp/B01AE35XKY) Convenient way to start using the popular ESP-01 ESP8266 module in your prototypes Clear pinout labels on the silkscreen for easily remembering the pinout of the ESP-01 Onboard 0.1µF decoupling capacitor for the ESP-01 to run smoothly!
    6.99 $
  • LuxtechPro Speech Recognition Module ELECHOUSE Voice Recognition V3 Interface 5V TTL Level UART/GPIO
    This module is a compact and easy-control speaking recognition board. It is a speaker-dependent voice recognition module. It supports up to 80 voice commands in all. Max 7 voice commands could work at the same time. Any sound could be trained as command. Users need to train the module first before let it recognizing any voice command. It has 2 controlling ways: Serial Port (full function), General Input Pins (part of function). General Output Pins on the board could generate several kinds of waves while corresponding voice command was recognized. We already know that Voice Recognition module V2 supports 15 commands in all and only 5 commands at the same time. On V2, voice commands are separated into 3 groups while you training it. And only one group (5 commands) could to be imported into Recognizer. It means only 5 voice commands are effective at the same time. On V3, voice commands are stored in one large group like a library. Any 7 voice commands in the library could be imported into recognizer. Parameters: Voltage: 4.5-5.5V, Current: <40mA, Digital Interface: 5V TTL level for UART interface and GPIO, Analog Interface: 3.5mm mono-channel microphone connector + microphone pin interface. Size: 31mm x 50mm. Recognition accuracy: 99% (under ideal environment). Features: Support maximum 80 voice commands, with each voice 1500ms (one or two words speaking). Maximum 7 voice commands effective at same time. Arduino library is supplied. Easy Control: UART/GPIO. User-control General Pin Output.
    38.89 $
  • DFRobot MDV 2x2A DC Motor Controller for Arduino (L298N)
    This MDV motor driver is able to drive 2 DC motors with voltage from 4.8 to 46V, each motor can have the current up to 2A. It is able to be controlled by Arduino. It can bear larger current due to the increased heat-sink dissipation It is easy to control, using a outstanding high-power motor driver chip, the L298N This chip allows for direct drive of two bi-directional DC motors, and incorporates high-speed short diodes for protection This breakout module with standard screw holes will help on applications and devices with flat spaces, so you don't need to use the Arduino stacked up shield
    17.99 $ 22.95 $ -22%
  • Keywish for Arduino mega 2560 Scratch Starter Kit,Super Base Kit for ATmega328P with 30 Lessons Tutorial Compatible with Arduino IDE Mixly Scratch Mblock Graphical Programming
    ✔THE MOST ECONOMICAL KIT FOR THE STARTER : This is the most basic Arduino kit for the beginner, has all the component you need to start Arduino. ✔EASY TO LEARN AND BRINGS A LOT OF FUN TO LEARNERS : Support Graphical Programming, based on Arduino platform to starting programming for those beginners who are interested. ✔100% COMPATIBLE WITH ARDUINO MEGA 2560 : Include High quality kit with development board. support Arduino IDE, Mixly, Mblock scratch graphical programming. ✔FREE DETAILED TUTORIALS : Tutorials CD including project introduction, libraries, source code and video, you can also download tutorials form the official website or contact us by Email to get documents.The Tutorials are pretty easy to follow and get you learning Ardunio in a pretty simple manner. ✔QUALITY PACKING AND GREAT GIFT IDEA : We provide exquisite packaging, All of the Components packing in a plastic box. It’s a perfect gift for children and frends in Christmas, New Year, Birthday, Party, Performance, Special occasions, Etc.
    39.99 $
  • Emakefun Development Board, Development Board for Arduino R3 with Micro Interface and BLE Wireless Module,Base on ATmega328P for Project
    Bluetooth module:Wirelessly connect your phone via APP Micro interface:You can use the data cable of your phone connect with computer Chip:ATmega328P,same as the official version Quality:Solder is Very Clean
  • Karlsson Robotics Arduino Project Enclosure
    allows you to easily enclose your Arduino main board, Arduino Mega, or some of the other board that fits the Arduino foot print Has room internally for an Arduino and a shield Has a snap-in compartment in the back for accessing switches or connections or battery access.