Coach teaches: Pcb 3d printer | Best choice

  • KOOBOOK 1Pcs 3D Printer Control Board Controller PCB Board MKS Gen L V1.0 Integrate Ramps Motherboard 12/24V
    2560 and ramps1.4 are intergrated on a piece of board, which solves the problem of complicated and easy failure for Ramps1.4 composite interface.Users can change their own motor drive, support 4988 drive and 8825 drive, TMC2100 drive. Using CH340 serial chip to ensure the stable and reliable premise, reduce the cost, and to solve the problem of the previous 16U2 hard drive.Using the open source firmware for Marlin, the configuration is exactly the same as for ramps1.4, and can replace for Ramps1.4 directly. 24V input can be accepted, and the same system power can reduce the hot bed current to 1/4, effectively solving the hot bed MOS tube heating problem. It can be directly connected to 2004LCD display and 12864LCD display, and can be supported by TFT28 and TFT32 touch screen. The XYZ axis adopts the terminals of different colors to correspond to the motor and the limit switch, and the connection is convenient,reduces the probability of inserting and reversing, and prevents the main board from being damage by the oppsite inserted of the drive.
  • MK2B Heated Bed with Soldered NTC 3950 Thermistor and Borosilicate Glass Sheet– 3D Printer PCB Heatbed for MakerBot RepRap UP Mendel I3 Printer
    PCB HEATBED: Keep your print model warm and malleable to improve adhesion and prevent warping during the printing process for a spectacular final result. GLASS SHEET: The heat bed combo includes a Borosilicate glass sheet suitable for high temperatures to create a flat, even surface. COMPATABILITY: MK2B 214mm x 214 mm (8.4 in x 8.4 in) 12V or 24V Hot Bed for MakerBot RepRap UP Mendel I3 Printer. NO SOLDERING REQUIRED: The PCB Heat Bed is supplied with integrated 100K ohm NTC 3950 Thermistor, and soldered power leads. AMX3D ACCESSORIES: The best 3D Prints start with the best tools! AMX3d provides 3D printing supplies of the highest quality. If there are any problems with your Heat Bed just let us know!
  • XLX 1220Pcs 2.54mm 2 3 4 5 6 7 8 9 Pin housing (and Pin Pedestal Housing) Kit and Male / Female Pin Header Terminals Connector Adapter Plug Set Compatible with JST XHP
    1.Pin Pitch : 2.54mm 2.Material : PVC , Metal 3. Pin : 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9 4. Quantity : 1220pcs with plastic box 5. Type : Compatible with JST-XHP
  • MKS Gen L V2.0 3D Printer Integrated Motherboard Controller PCB Board A4988/DRV8825/TMC2208/TMC2130 Like Ramps 1.6 MKS Gen V1.4 Mainboard 1PCS
    ฅฅ Integrate 2560 and Ramps1.4 one PCB,easier wiring and more stable ฅฅ Use high-quality 4 layer PCB&Use special power chip,support 12V-24V, also Use Marlin firmware,same as configuration way as Ramps1.4, it can replace Ramps1.4 directly ฅฅ Support a variety of stepper drivers:4988,8825,TMC2208 and TMC2100, and available to work with LCD2004,LCD12864,MKS ฅฅ TFT24/28/32/35 & Available to connect external large stepp drivers Accept 24V input,reduce the heated bed current to 1/4 that slove the Mosfet heat problem efficiently ฅฅ Retail Servos,AUX-1 and AUX-2 interface of Ramps1.4 provide three 5V output and three 12V output interfaces
    21.29 $
  • Creativity 3D Printers Parts Heated Bed 24V Heatbed Platform 235/310mm PCB Heat Aluminum Plate with Heat Insulation Cotton for Ender3 3D Printer (310310mm)
    【3D printer Heat Bed Size & Voltage 】 24V 220W Heater Bed Aluminum with Cable Installed and Build Surface Plate,come in size 310 * 310 * 3mm, easy and quick to install, strong and durable. 【Creativity 3d printer Aluminum Heated 】The plate is made with high quality aluminium alloy material, with great heat performance, do not worry about printing warping edge problem. 【Excellent Heating Performance 】The plate is used as a perfect replacement accessory for 3D printer, to guarantee the efficient operation the 3D printersheat up to 100℃ within 5mins. 【Upgraded Version】Upgraded hot bed plate with heat insulation cotton, which improves the heat conduction and heat-resistance performance. Creativity Team provides 3D printing supplies of the highest quality. If there are any problems with your Heat Bed just let us know!
    20.99 $
  • Retermit 2 Rolls 10mm X100ft Kapton Tape Sublimation Tape - for Heat Transfer Vinyl,3D Printers High Temperature Tape PCB Tape Heat Resistant Tape Heat Tape
    Perfect for protecting sensitive printed circuit board (PCB) components such as gold fingers when wave soldering Extensive use as heat tape for transformer, motor, coil, capacitor and frequency conversion power supply in electronic industry. Transfer tape for vinyl.This heat transfer tape keep your design in place when you making shirts and hats,help to do heat transfer vinyl on a heat press. Size: Width: about 10mm/0.39in; Length: about 30m /100ft. Heat resistance: about 260C/500F
    6.49 $
  • DGZZI 2PCS DRV8825 for RAMPS Stepper Motor Driver Module 3D Printer Accessaries Heat Sink 4 Layer PCB Purple Board
    Suitable for driving 8.2V~45V below 2.5A stepper motor; There are only simple stepping and direction control interfaces; Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step; The adjustable potentiometer can adjust the maximum current output to obtain higher step rate; Automatic current attenuation mode detection/selection;Overheating off circuit, under voltage lock, cross current protection;Ground short circuit protection and load short circuit protection.
    8.99 $
  • Aoicrie MKS Gen L V1.0 3D Printer Integrated Mainboard Controller PCB Board Compatible Ramps1.4/Mega2560 R3 with A4988 Motor Driver for 3D
    Integrate 2560 and Ramps1.4 one PCB,which designed to avoid complicated connections, easier wiring and more stable Use high-quality 4 layer PCB&Use special power chip,support 12V-24V, also Use Run Marlin firmware,same as configuration way as Ramps1.4, it can replace Ramps1.4 directly. Use high quality MOSFET tube,better cooling and more stable.Use special power chip,support 12-24V input,reduce the heated bed current to 1/4 that slove the Mosfet heat problem efficiently and power shortage. Support a variety of stepper drivers: A4988,DRV8825,TMC2208 and TMC2100, and available to work with LCD2004,LCD12864,MKS TFT24/28/32/35 & Available to connect external large stepp drivers, A4988 driver board widely used in 3D printers and small CNC machines. Support functions: Non-trace resumption after power off, run out filament ,and auto shut down, XTZ axis with different color terminal controls the motors and end stop,which is convenient to wire.Use high-quality 4 layer PCB&Use special power chip.Retail Servos,AUX-1 and AUX-2 interface of Ramps1.4 provide three 5V output and three 12V output interfaces. Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step.Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage toachieve higher step rates.Use the configuration file to set the driving current mode, avoid manual adjustment of the current to cause the burned drive, convenient, safe and reliable.
    34.99 $
  • DollaTek 3MM MK3 Aluminum Board PCB Heated Bed for Reprap Standard 3D Printer
    1 layer 35μm copper Voltage: 12/24V The new circuit, whether meet the 12V or 24 v, the power is stable. Heating Time: 24V reaches 100°C in 2 minutes Max. Temp: 180°C