Answers to: Arduino robot obstacle avoidance | Complete Test

  • HiLetgo 10pcs IR Infrared Obstacle Avoidance Sensor Module for Arduino Smart Car Robot 3-Wire Reflective Photoelectric for Arduino Smart Car Robot
    Can be widely used in robot obstacle avoidance, obstacle avoidance car, line count, and black and white line tracking and so on. The effective distance range of 2 ~ 30cm, the working voltage of 3.3V- 5V
  • TFmini-s Lidar Sensor 0.1-12m Measurement Range Distance Single-Point Ranging Finder Module UART / I2C Compatible with Pixhawk,Arduino and Raspberry Pi for Drone/Robot Obstacle Avoidance
    [Upgraded TFmini Lidar Module] TFmini-s, based on TFmini, is a single-point short-range LiDAR sensor. Inherited characters of low cost, small size and low power consumption from TFmini,which greatly improved its performance [High Performance] TFmini-s accuracy can reach up to ±1% at full range distance of 12m,increasing the measurement frequency to 1000Hz. The dead zone is shortened to 10 cm improving accuracy and stability. Ambient light immunity is 70Klux and central wavelength is 850nm,but it only keep 5.3g at weight [Low Power Yet High Frame Rate] In low power consumption mode, the maximum power consumption can be lower than 100mW, reducing system power consumption and further prolonging LiDAR lifetime [Optional Commutication Interfaces] To improve applicability, TFmini-s supports common communication interfaces — UART, IIC and IO.TFmini-s version is UART by default. If you need IIC, please switch by yourself. It also compliant with CE,RoHs,and FCC certification
  • OSOYOO 10PCS IR Infrared Obstacle Avoidance Sensor Module for Arduino Smart Car Robot Raspberry PI 3.
    IR Infrared Obstacle Avoidance Sensor Module can be widely used in robot obstacle avoidance, obstacle avoidance car, line count, and black and white line tracking and so on. the module detects the distance 2 ~ 30cm, detection angle 35 °, the distance can detect potential is adjusted The output port OUT sensor module can be directly connected to the microcontroller IO port, you can directly drive a 5V relay. It has a pair of infrared transmitting and receiving tube, tube infrared emit a certain frequency, when detecting direction meet with obstacles (reflecting surface), reflected infrared receiving tube, after the comparator circuit processing, green indicator will light up, at the same time signal output interface to output digital signal (a low level signal). Can be used for 3-5V DC power supply modules. It has red power indicator.
  • 10PCS IR Infrared Obstacle Avoidance Sensor Module for Arduino Smart Car Robot
    6.88 $
  • Magic&shell 3PCS IR Infrared Obstacle Avoidance Sensor Module for Arduino Raspberry PI Smart Car Robot 3.3V-5V
    Type: IR Infrared Obstacle Avoidance Sensor Module. Detection distance: 2 ~ 20cm . Detection angle: 35 Degrees. Size:32x14mm/1.26x0.55Inches. Package Contents: 3PCS. The comparator is LM393. Working stabilization. Be adjusted by potentiometer and has the characteristics of small interference, easy assembly and convenient use. Widely used in robot obstacle avoidance, obstacle avoidance car, line count, and black and white line tracking and so on .
    6.99 $
  • Aceirmc 10pcs IR Infrared Obstacle Avoidance Sensor for Arduino Smart Car Robot IR Transmitting and Receiving Tube Photoelectric Switch
    The output port OUT sensor module can be directly connected to the microcontroller IO port, you can directly drive a 5V relay. It has a pair of infrared transmitting and receiving tube, tube infrared emit a certain frequency, when detecting direction meet with obstacles (reflecting surface), reflected infrared receiving tube, after the comparator circuit processing, green indicator will light up, at the same time signal output interface to output digital signal (a low level signal). Can be used for 3-5V DC power supply modules. It has red power indicator. the Sensor module detects the distance 2 ~ 30cm, detection angle 35 °, the distance can detect potential is adjusted IR Infrared Obstacle Avoidance Sensor Module can be widely used in robot obstacle avoidance, obstacle avoidance car, line count, and black and white line tracking and so on.
    8.29 $
  • 5pcs IR Infrared Obstacle Avoidance Sensor IR Transmitting and Receiving Tube Photoelectric Switch 3-pin Compatible with Ar-duino Smart Car Robot
    ☆The sensor module has strong ability to adapt to ambient light. It has a pair of infrared transmitting and receiving tubes. The transmitting tube emits infrared light of a certain frequency. ☆Signal output interface outputs a digital signal (a low-level signal). The detection distance can be adjusted by the potentiometer knob. The effective range is 2 to 30cm and the working voltage is 3.3V.5V. ☆The sensor's detection distance can be adjusted by a potentiometer, has small interference, is easy to assemble, and is easy to use. ☆It can be widely used in robots to avoid obstacles, avoid cars, count pipelines, and track black and white lines. ☆Sensor module output port OUT can be directly connected with the microcontroller IO port can also directly drive a 5V relay; connection mode: VCC-VCC; GND-GND; OUT-IO.
    13.99 $
  • 20 Pieces IR Infrared Obstacle Avoidance Sensor Module 3-Wire Reflective Photoelectric Sensor Module Compatible with Arduino Smart Car Robot Raspberry Pi 3
    Feature: there is a pair of infrared transmitting and receiving tube of the IR sensor module, tube infrared emit a certain frequency, when the detection direction meets the obstacles (reflecting surface), reflected infrared receiving tube, after the comparator circuit processing, green indicator will light up, at the same time signal output interface to output digital signal (a low level signal) Function: the IR infrared obstacle avoidance sensor module can be applied in robot obstacle avoidance, obstacle avoidance car, line count, black and white line tracking, etc. Adjustable distance: the detection distance of the infrared module is 2 to 30 cm, and the detection angle is 35 degrees, the distance The distance at which the potential can be detected is adjustable Easy to use: the output port OUT sensor module can be directly connected to the microcontroller IO port, you can directly drive a 5V relay Application: the IR sensor module can be applied for 3-5V DC power supply modules; There is a red power indicator
    11.99 $
  • Gowoops Infrared Photoelectric Sensor E18-D80NK Obstacle Avoidance for Arduino Robot Car
    E18-D80NK is a set of transmitter and receiver in one of the photoelectric sensor Detection distance can be adjusted according to requirements Long distance detection, low visible light interference, cheap price, easy assembly, and easy to use Can be widely used in robot obstacle avoidance, pipeline line piece and many other automation products
  • FTCBlock 10PCS IR Infrared Obstacle Avoidance Sensor Module for Arduino Smart Car Robot
    IR Infrared Obstacle Avoidance Sensor Module can be widely used in robot obstacle avoidance, obstacle avoidance car, line count, and black and white line tracking and so on. The module detects the distance 2 ~ 30cm, detection angle 35 °, the distance can detect potential is adjusted. The output port OUT sensor module can be directly connected to the microcontroller IO port, you can directly drive a 5V relay. It has a pair of infrared transmitting and receiving tube, tube infrared emit a certain frequency, when detecting direction meet with obstacles (reflecting surface), reflected infrared receiving tube, after the comparator circuit processing, green indicator will light up, at the same time signal output interface to output digital signal (a low level signal). Can be used for 3-5V DC power supply modules. It has red power indicator.